calage distribution infiniti fx35

Aller en bas

calage distribution infiniti fx35

Message par Admin le Sam 2 Déc - 0:18

TIMING CHAIN 

Installation 

NOTE: 
The figure shows the relationship between the mating mark on each timing chain and that on the corresponding sprocket, the components installed.
[Vous devez être inscrit et connecté pour voir cette image]
Install the rear timing chain case, if removed. Refer to See: Timing Cover\Service and Repair\Rear Timing Chain Case.
Install the timing chain tension guide.
[Vous devez être inscrit et connecté pour voir cette image]
Position the crankshaft so No. 1 piston is set at TDC on the compression stroke.
Make sure that the dowel pin hole, dowel pin and crankshaft key are located as shown. Camshaft dowel pin hole (intake side): at cylinder head upper face side in each bank.
Camshaft dowel pin (exhaust side): at cylinder head upper face side in each bank.
Crankshaft key: at cylinder head side of RH bank.

CAUTION: 
Hole on small diameter side must be used for intake camshaft sprocket dowel pin. Do not misidentify (ignore big diameter side). 

[Vous devez être inscrit et connecté pour voir cette image]

Install the secondary timing chains and camshaft sprockets.
CAUTION: 
Matching marks between the timing chain and sprockets slip easily. Confirm all matching mark positions repeatedly during the installation process. 
Push the sleeve of the secondary chain tensioner and keep it pressed in with a stopper pin.
Align the matching marks (4), (5), (7) and (10) on the secondary timing chain (Cool (orange link) with the ones on the intake and exhaust sprockets (stamped), and install them.
Matching marks for the intake sprocket are on the back side of the secondary sprocket.
There are two types of matching marks, round (7) and (10) oval (4) and (5) types. They should be used for the RH and LH banks, respectively. RH bank: use round type (7) and (10).
LH (6) bank: use oval type (4) and (5).
Align the dowel pin (3) with and pin hole on the camshaft sprocket INT side (1), and dowel pin groove (11) with the dowel pin on the camshaft EXH side, and install them.

[Vous devez être inscrit et connecté pour voir cette image]

On the intake side, align the pin hole on the small diameter side of the camshaft front end with the dowel pin (3) on the back side of the camshaft sprocket (1), and install them.
On the exhaust side, align the dowel pin on the camshaft front end with the dowel pin groove (11) on the camshaft sprocket (9), and install them.
Camshaft sprocket bolts must be tightened in the next step. Tightening them by hand is enough to prevent the dislocation of the dowel pins (3) and dowel pin grooves (11).

[Vous devez être inscrit et connecté pour voir cette image]

It may be difficult to visually check the dislocation of mating marks during and after installation. To make the matching easier, make a mating mark on the sprocket teeth in advance with paint.
After confirming the mating marks are aligned, tighten the camshaft sprocket bolts.

[Vous devez être inscrit et connecté pour voir cette image]

Secure the camshaft using a wrench at the hexagonal portion to tighten the bolts.
Pull the stopper pins out from the secondary timing chain tensioners.

[Vous devez être inscrit et connecté pour voir cette image]

Install the crankshaft sprocket on the crankshaft.
Make sure the mating marks on the crankshaft sprocket face the front of the engine.

[Vous devez être inscrit et connecté pour voir cette image]

nstall the primary timing chain.
Install primary timing chain so the mating mark (punched) (B) on camshaft sprocket (C) is aligned with the pink link (A) on the timing chain, while the mating mark (notched) (E) on the crankshaft sprocket (D) is aligned with the orange one (F) on the timing chain, as shown.
When it is difficult to align mating marks of the primary timing chain with each sprocket, gradually turn the camshaft using a wrench on the hexagonal portion to align it with the mating marks.
During alignment, be careful to prevent dislocation of mating mark alignments of the secondary timing chains.

[Vous devez être inscrit et connecté pour voir cette image]

 Water pump
Install the internal chain guide and slack guide.

[Vous devez être inscrit et connecté pour voir cette image]

CAUTION: 
Do not overtighten the slack guide bolts. It is normal for a gap to exist under the bolt seats when the bolts are tightened to specification.
Install the timing chain tensioner for the slack guide.

[Vous devez être inscrit et connecté pour voir cette image]

When installing the chain tensioner, push in the sleeve and keep it pressed in with the stopper pin.
Remove any dirt and foreign materials completely from the back and the mounting surfaces of the chain tensioner

[Vous devez être inscrit et connecté pour voir cette image]

After installation, pull out the stopper pin while pressing the slack guide.
Reconfirm that the matching marks on the sprockets and the timing chain have not slipped out of alignment.

[Vous devez être inscrit et connecté pour voir cette image]

Install new O-rings (A) on the rear timing chain case.
Install the front timing chain case. Refer to See: Timing Cover\Service and Repair\Front Timing Chain Case.
Activate the fuel system. Check for any leaks when the system is repressurized and correct as necessary.
Start the engine and check all systems for leaks or improper operation. Correct as necessary.
avatar
Admin
Admin
Admin

Messages : 60
Date d'inscription : 15/08/2017
Localisation : https://www.otmec.net/

https://www.otmec.net/

Revenir en haut Aller en bas

Revenir en haut


 
Permission de ce forum:
Vous ne pouvez pas répondre aux sujets dans ce forum